![]() ![]() NEVER connect high pressure hose to nozzle extension.resulting in serious ) injury and possible amputation. WARNING: The high pressure stream of water that this equipment produces could cut through skin and its underlying tissues. Uncoil high pressure hose and attach one end of hose to base of spray gun. Damage to equipment resulting from failure to follow this instruction will void warranty.ġ.NOTICE: DO NOT run the pump without the water supply connected and turned on. Use a small brush or cotton swab to apply grease directly to o-rings where they are not accessible (QC fii.Use lubricants sparingly during assembly a light film is all that is required.Inspect and clean connecting surfaces prior to lubrication and assembly.NOTICE ALWAYS apply a small amount of lubricant on co-rings prior to assembling the garden hose to the pump (A). pinching or cutting and extends the life of the o-ring. It also helps protect the o-ring from damage by abrasion. The use of a lubricant (petroleum or synthetic grease) during assembly helps seat o-rings properly and provides an improved seal. Lubrication of o-rings is extremely important for installation and operation. (762 m) with the high altitude kit is not recommended. Operation of the engine at altitudes below 2. See an Authorized Briggs & Stratton dealer for high altitude adjustment information. Operation without this adjustment will cause decreased performance, increased fuel consumption. To remain emissions compliant, high altitude adjustment is required. (1524 m), a minimum 85 octane / 85 AKI (89 RON) gasoline is acceptable. Install fuel cap and let any spilled fuel evaporate before starting engine. do not fill above the bottom of the fuel tank neck.ģ. Slowly add regular unleaded fuel (A) to fuel tank (B). Check fuel lines, tank, cap and fittings frequently for cracks or leaks.Keep fuel away from sparks, open flames, pilot lights, heat.If fuel spills, wait until it evaporates before starting engine. Loosen cap slowly to relieve pressure in tank. Turn pressure washer engine OFF and let it cool at least 2 minutes before removing fuel cap.fire or explosion resulting a in death or serious injury. WARNING: Fuel and its vapors are extremely flammable and explosive which could cause burns. The emission control system for this engine is EM (Engine Modifications). This engine is certified to operate on gasoline. switch to a different fuel provider or change brands. If you experience starting or performance problems after using fuel. mix in a fuel stabilizer when adding fuel. To protect the fuel system from gum formation. DO NOT mix oil in gasoline or modify engine to run on alternate fuels.DO NOT use unapproved gasoline such as £15 and E85.NOTICE: Use of unapproved fuels could damage pressure washer and voids warranty. Gasoline with up to 10% ethanol (gasohol) is acceptable.For high altitude use, see High Altitude. A minimum of 87 octane/87 AKI (91 RON).Replace oil fill cap/dipstick and fully tighten.DO NOT attempt to crank or start the engine before it has been properly serviced with the recommended oil. NOTICE: Improper treatment of pressure washer could damage it and shorten its life. Wipe dipstick clean each time oil level is checked. fill to FULL mark (top hole) on dipstick. Slowly pour contents of oil pouch into oil fill opening.Hold neck of supplied oi! pouch and remove cap.Clean area around oil fill and remove yellow oil fill cap/dipstick.Squeeze hose hook wireform (J) together and insert into grooves at bottom of accessory tray.Attach rope guide (G) through handle with plastic knob (H).Push tree clips (F) into the holes until they sit flat against the accessory tray. Place accessory tray (D) over holes (E) on handle (viewing from front of unit).Insert carriage bolts (B) through holes from inside of unit and attach a plastic knob (C) from outside of unit.Make sure holes in handle align with holes on handle supports. Place handle (A) onto handle supports connected to main unit.Bag of 4 Multi-Colored Quick Connect Spray Tips.Parts Bag (which includes the following):.Ensure you have all included items prior to assembly.Open carton completely by cutting each corner from top to bottom.Remove the parts bag, accessories, and inserts included with pressure washer.If calling for assistance, please have the model, revision, and serial number from the identification label available. If you have any problems with the assembly of your Pressure washer, please call the pressure washer helpline. Your pressure washer requires some assembly and is ready for use after it has been properly serviced with the recommended oil and fuel. Read entire operator's manual before you attempt to assemble or operate your new pressure washer. Operator's Manual Pressure Washer Assembly Craftsman CMXGWAS020734 3000-PSI Cold Water Gas Pressure Washer - Use Manual - Use Guide PDF.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |